Stacker & Reclaimer Procurement from China
Specification, Audit & Pre-Shipment Inspection
Stackers and reclaimers are long-lead, site-specific machines where the specification strongly influences cost and the engineering and production capability of the manufacturer affects project performance. We help overseas buyers specify, evaluate and purchase them from vetted Chinese manufacturers.
From technical specification and supplier shortlisting to factory audit, pre-shipment inspection and shipment coordination — the right manufacturer depends on your capacity, material and yard layout, so we shortlist qualified manufacturers per project rather than push a fixed catalogue.
What we do for you
Technical specification
We turn your process requirement into a written technical specification that manufacturers can be compared against — capacity, materials, duty, standards and inspection requirements.
Supplier shortlisting
We shortlist qualified manufacturers for each project and compare their proposals against your capacity, material and site conditions, so the recommendation follows your actual duty.
Factory audit
We assess production capacity, welding and machining capability, quality systems and export experience before a manufacturer is recommended.
Quality control and inspection
We review drawings and material certificates during manufacture, and carry out dimensional checks and pre-shipment inspection before anything leaves the factory.
Commercial and contract support
We support specification of payment terms, delivery milestones, inspection and acceptance conditions and documentation, so the contract reflects what was actually agreed.
Logistics coordination
We coordinate packing, marking, shipment and export documentation, including disassembly planning and packing lists for oversized assemblies.
How the process works
- 1
You send the process requirement, site conditions and the budget range.
- 2
We prepare a written technical specification and confirm it with you.
- 3
We shortlist qualified manufacturers and compare their proposals on the same basis.
- 4
We audit the shortlisted manufacturers, clarify technical and commercial points with them, and present the results for your decision.
- 5
We monitor manufacture, review drawings and certificates, and witness testing.
- 6
We carry out pre-shipment inspection and coordinate packing, shipment and documentation.
What to tell us when you enquire
This is the information we need to write a specification and compare manufacturers on the same basis. Partial data is fine — we will tell you what is missing.
Specification and site data
| Stacking capacity | tph, and whether it is continuous or intermittent |
|---|---|
| Reclaiming capacity | tph, and the reclaim method — bucket wheel, scraper or drum |
| Yard layout | circular or linear stockyard, pile cross-section, stockpile volume |
| Machine geometry | boom length in m, rail gauge in m, slewing range, travel length |
| Material | bulk density in t/m³, lump size, moisture, abrasiveness, angle of repose |
| Power supply | voltage and frequency at site, cable reel or trailing cable arrangement |
| Automation level | manual, semi-automatic or automatic stockyard control |
| Site conditions | wind load, seismic zone, temperature range, dust and corrosion |
Key components we also supply
The drive and control package can be supplied with the machine or separately. Supplying both keeps the mechanical and electrical interface consistent, and means the spares are available from the same place.
Motors and variable speed drives
- Innomotics SIMOTICS low-voltage and medium-voltage motors
- ABB IEC, NEMA and IE5 SynRM motors
- WEG W22, W51 HD and medium-voltage ranges
- Siemens SINAMICS and ABB ACS drives
Gearboxes, couplings and holdbacks
- Flender FZG helical and bevel-helical gear units, 3,100 – 1,400,000 Nm
- Flender FLENDER ONE and geared motors
- Flender FLUDEX fluid couplings
- Flender N-EUPEX, RUPEX, ARPEX and ZAPEX couplings
Automation and control
- Siemens SIMATIC S7-1200 / S7-1500 and ET 200 distributed I/O
- B&R X20 system, industrial PCs and ACOPOS servo drives
- HMI, motor protection and condition monitoring
Boom conveyor and travel drives
- Boom belt conveyor drives
- Slewing drives and bearings
- Travel drives and rail wheels
- Bucket wheel drives
Drive packages for this equipment
Related services
Component brands we supply
Service & support
Remote and on-site support available, from installation supervision to commissioning and troubleshooting.
Why work with us
- We shortlist manufacturers per project and compare their proposals against your specification, conditions and budget.
- Key requirements are documented throughout — specifications, drawings, certificates and inspection reports.
- We inspect during manufacture and again before shipment, so problems surface at the factory, not at your site.
- We also supply the drive components, so the mechanical and electrical interfaces stay consistent.
Service & support
Remote and on-site support available, from installation supervision to commissioning and troubleshooting.
What we need from you to quote
- Equipment type and required capacity
- Site conditions, power supply and any drawings you have
- Required standards, inspection level and documentation
- Budget range, delivery window and destination port
Looking for a machine that is not listed here?
These are the machines clients ask us for most, not the limit of what we handle. If you are procuring any other type of industrial equipment from China, send us the specification, the drawings, or a photo of the nameplate. We shortlist qualified manufacturers, review the technical proposals, audit the works, inspect before shipment and coordinate export delivery.
Send us the requirementAnswers before you ask
Frequently asked questions
What exactly do you do for a stacker-reclaimer purchase?
We prepare the technical specification, shortlist qualified Chinese manufacturers, audit them, monitor manufacture, witness testing and carry out pre-shipment inspection, then coordinate packing, shipment and documentation.
Can you name the manufacturers you work with?
We shortlist per project rather than publish a fixed list, because the right manufacturer depends on your capacity, material and site conditions. We disclose the shortlisted manufacturers to you before you decide.
Do you only supply the eight brands shown on your homepage?
No. We source and supply spare units and parts for most international and Chinese industrial brands, not only the eight brands shown on this site.
I do not know the exact model number. Can you still quote?
Yes. Send us a photo of the nameplate and we will identify the exact unit before preparing the quotation for the original part.
Do you supply genuine original manufacturer parts?
Yes. We supply genuine original manufacturer parts. Send us a photo of the nameplate and we can identify the exact unit before quoting, so you do not need to look up a model number.
Do you provide installation guidance, commissioning and after-sales support?
Yes. We provide installation guidance, commissioning support and after-sales support, remotely or on site depending on your project.
What is the delivery time?
Lead time depends on the product and configuration. We confirm the delivery schedule together with the quotation, so you have a firm date before you order.
Which export documents and certificates can you provide?
We can provide applicable CE and ISO documentation, certificates of origin, packing lists and test reports according to the requirements of your destination country.
What payment terms and incoterms do you work with?
We accept T/T and L/C payment, and quote FOB, CIF or EXW terms to suit your project.
Tell us the requirement and we will shortlist qualified manufacturers
We select manufacturers based on your requirements. We prepare the technical specification, compare qualified manufacturers on a consistent basis, and inspect before anything ships.
Discuss Your Requirement